1. Do not share user accounts! Any account that is shared by another person will be blocked and closed. This means: we will close not only the account that is shared, but also the main account of the user who uses another person's account. We have the ability to detect account sharing, so please do not try to cheat the system. This action will take place on 04/18/2023. Read all forum rules.
    Dismiss Notice
  2. For downloading SimTools plugins you need a Download Package. Get it with virtual coins that you receive for forum activity or Buy Download Package - We have a zero Spam tolerance so read our forum rules first.

    Buy Now a Download Plan!
  3. Do not try to cheat our system and do not post an unnecessary amount of useless posts only to earn credits here. We have a zero spam tolerance policy and this will cause a ban of your user account. Otherwise we wish you a pleasant stay here! Read the forum rules
  4. We have a few rules which you need to read and accept before posting anything here! Following these rules will keep the forum clean and your stay pleasant. Do not follow these rules can lead to permanent exclusion from this website: Read the forum rules.
    Are you a company? Read our company rules
Shared accounts will be removed Plugin Downloads Zero spam policy Forum Rules

ordered a new toy (CNC Plasma)

Discussion in '3D Printing' started by crammy, Dec 16, 2016.

  1. crammy

    crammy Active Member Gold Contributor

    Joined:
    Feb 23, 2016
    Messages:
    563
    Occupation:
    Fabrication
    Location:
    essex
    Balance:
    4,633Coins
    Ratings:
    +326 / 2 / -0
    My Motion Simulator:
    SCN6, 4DOF
    Hi All

    Probably in the wrong section so please move if it is.

    I've ordered a cnc plasma table(not personally but for my company) capable of cutting 40mm mild steel plate so it's not to bad. It should arrive and be setup by the end of January which is perfect timing for me as i'm going to start my 2nd project. I can cut all the Aluminium floor plates and put holes in accurately so all should be perfect and pretty straight forward.
    I wouldn't mind building a decent set of pedals, so have any of you, got or seen any plans for some.

    Also I'm looking out for sim bits i can make so if any of you UK based people have anything you need ill try and make them for you at cost of material plus postage if i can. I'm more than happy to help the community

    cheers

    Jay
    • Friendly Friendly x 3
    • Like Like x 2
    crammy, Dec 16, 2016
    #1
  2. bruce stephen

    bruce stephen Hammer doesnt fix it, must be electrical

    Joined:
    Jun 7, 2015
    Messages:
    1,286
    Occupation:
    general contractor
    Location:
    michigan
    Balance:
    9,112Coins
    Ratings:
    +1,238 / 9 / -0
    My Motion Simulator:
    2DOF, DC motor, Arduino, Motion platform, 6DOF
    @crammy do you play Iracing? Beano has a write up, there in the forums under hardware or DIY controllers can't remember which. He uses Tilton or something similar. Either way he shows his pedal project. Also Jason Jodarski built a few sets and can also help.
    bruce stephen, Dec 16, 2016
    #2
  3. crammy

    crammy Active Member Gold Contributor

    Joined:
    Feb 23, 2016
    Messages:
    563
    Occupation:
    Fabrication
    Location:
    essex
    Balance:
    4,633Coins
    Ratings:
    +326 / 2 / -0
    My Motion Simulator:
    SCN6, 4DOF
    Thanks @bruce stephen.
    I'll join the forum and have a look.
    I've not got I racing sorted yet but will definatly when I get my new wheel.
    • Like Like x 1
    crammy, Dec 17, 2016
    #3
  4. ferslash

    ferslash Active Member

    Joined:
    Feb 8, 2011
    Messages:
    495
    Balance:
    4,798Coins
    Ratings:
    +181 / 2 / -0
    envy is a capital sin right? :D:D:D:D so i will say that i dont envy you :D:D:D:D
    ferslash, Dec 17, 2016
    #4
  5. crammy

    crammy Active Member Gold Contributor

    Joined:
    Feb 23, 2016
    Messages:
    563
    Occupation:
    Fabrication
    Location:
    essex
    Balance:
    4,633Coins
    Ratings:
    +326 / 2 / -0
    My Motion Simulator:
    SCN6, 4DOF
    lol @ferslash . happy to try and make some bits for you if your in the uk, however don't count your chickens as me and tech don't get om. my 4 week old rift has no screen on anything. just got the orange light
    • Like Like x 1
    crammy, Dec 17, 2016
    #5
  6. noorbeast

    noorbeast VR Tassie Devil Staff Member Moderator Race Director

    Joined:
    Jul 13, 2014
    Messages:
    21,048
    Occupation:
    Innovative tech specialist for NGOs
    Location:
    St Helens, Tasmania, Australia
    Balance:
    147,986Coins
    Ratings:
    +10,884 / 54 / -2
    My Motion Simulator:
    3DOF, DC motor, JRK
    Have you contacted Oculus Support and what are your system specs, plus what USB ports are you using?
    noorbeast, Dec 17, 2016
    #6
  7. crammy

    crammy Active Member Gold Contributor

    Joined:
    Feb 23, 2016
    Messages:
    563
    Occupation:
    Fabrication
    Location:
    essex
    Balance:
    4,633Coins
    Ratings:
    +326 / 2 / -0
    My Motion Simulator:
    SCN6, 4DOF
    panic over. it was my mate somehow getting into my home network .he literally took over all my shit from an s7 edge. he just just did it to get me off the seat as the women (our other halves) were boring him
    crammy, Dec 18, 2016
    #7
  8. Historiker

    Historiker Dramamine Adict Gold Contributor

    Joined:
    Dec 16, 2010
    Messages:
    2,160
    Occupation:
    Retired
    Location:
    Michigan USA
    Balance:
    9,195Coins
    Ratings:
    +2,161 / 19 / -1
    My Motion Simulator:
    3DOF, DC motor, Arduino, Motion platform, 6DOF
    Moved for you. We do not really have a cnc section, this is as close as we get but perhaps we should edit the section title?
    Historiker, Dec 19, 2016
    #8
  9. crammy

    crammy Active Member Gold Contributor

    Joined:
    Feb 23, 2016
    Messages:
    563
    Occupation:
    Fabrication
    Location:
    essex
    Balance:
    4,633Coins
    Ratings:
    +326 / 2 / -0
    My Motion Simulator:
    SCN6, 4DOF
    crammy, Dec 19, 2016
    #9