Question sabertooth and arduino uno setting - need your support

Hallo everyone.
In 2014 I built my first simulator using jrk12v12 cards.Thanks to the availability and assistance received from you I have managed to configure the cards and simtools. In particular earobbie (rob) helped me by dedicating me a few hours of her time and with skype we managed to run the sim.I have a decent manual but for any amount of electronics I have none, just no knowledge and for me it is really complicated to be able to configure. To this is added the fact that my English is schooling and using google translator often the explanations remain incomprehensible. Often I am forced to ask questions that many of you may consider stupid questions, but read with the eyes of those who really have no electronic knowledge seem insurmountable obstacles. Sorry for this.
For my new project I chose the most powerful engines and consequently the sabertooth 2x32 cards and arduin one. This is my project https://www.xsimulator.net/community/threads/4dof-by-gigifux.9734/page-2#post-130145 .
I tried to follow the tutorial https://www.xsimulator.net/communit...ket-serial-pid-motor-driver-w-softstart.9277/ but unfortunately I did not succeed and I fear that without your help I will never succeed. The board communicates with arduino but I can not move the motor.
I know that for many of you the configuration is simple and perhaps even intuitive. I unfortunately do not understand anything.For that I ask for your help through skype or teamwiever. Otherwise I have to give up this kind of configuation and go back to old engines and jrks that thanks to earobbie I have become almost familiar.
I thank them all who will help and support me
gigi

gday mate im using sabertooth 2x60 have you set the baud rate in the software..

Hi evan
yes I set 115200 in describe
I don't know how set serial timeouts at 100 m/s . describe show "s" and not m/s so I try to write 0,010 but not accepted. so I wrote 100 but I don't know if this mean 100 s or 100 m/s

ok well i use the 2x60 and it auto baud i dont need the software so i cant help you with that sorry. but ill have a look and see if i can help u bro

Thank s Evan

these are my descibe set and smc3 set

Hello,
Try this one https://www.xsimulator.net/community/threads/smc3-sabretooth-test-version.6236/
for me that's working. But i using sabertooth 2x25. And in sketch need to change serial boud rate from 500000 to 115200 because with 500000 motion really jerky. In Simtools serial interface should leave 500000

From sketch;
//****************************************************************************************************************
// Arduino setup subroutine called at startup/reset
//
//****************************************************************************************************************


void setup()
{
Serial.begin(500000); //115200 (500000 change to 115200 if not working )
// set the data rate for the SoftwareSerial port
#ifdef SECOND_SERIAL
mySerial.begin(115200);
#endif
#ifdef MODE3
mySerial.begin(38400);
#endif
OutputPort=PORTD;
pinMode(ENApin1, OUTPUT);
pinMode(ENBpin1, OUTPUT);
pinMode(ENApin2, OUTPUT);
pinMode(ENBpin2, OUTPUT);
pinMode(ENApin3, OUTPUT);
pinMode(ENBpin3, OUTPUT);
pinMode(PWMpin1, OUTPUT);
pinMode(PWMpin2, OUTPUT);
pinMode(PWMpin3, OUTPUT);
#ifndef MODE3
MyPWMWrite(PWMpin1,0); //analogWrite(PWMpin1, 0);
MyPWMWrite(PWMpin2,0); //analogWrite(PWMpin2, 0);
analogWrite(PWMpin3, 0);
#endif
DisableMotor1();
DisableMotor2();
DisableMotor3();

// Note that the base frequency for pins 3, 9, 10, and 11 is 31250 Hz

"PWMmax"should be more than 0 , begin from 150 and up...

thanks auryza but As I write before, I have not any knowledge about arduino and it's very difficolut for me. So before try wht you suggest it's that someone help me to reinstal arduino, smc3 and set all with t
parameters. for thisIsuggest teamwiever
to do wht you suggest it's necessary have basic knowledge that I not have
Inany case thanks for your reply

one thing i just noticed is in smc3 my calcs/sec is 100
your is 1001 could this be my issue

i worked out my frid was 10 thats why it was 100 if i put it to 1 like yours my motors had a delay from m1 to m2

The tutorial specify to set it At 100 m/s . Describe string show "s" and not m/s so if you write 100 it should mean 100 s and not 100 m/s. For these reason i wrote 0,01 s that mean 100 m/s. But if in correct i write 100.
Another important question....where i can set the range of my my motors lever. In describe software? My motor lever should have 90degrees of range (45degrees forward and 45backward from the center)

this is my arduino configuration
Is it correct?

At the moment I have connected only one motor to my card.
what does men these strings in ide?:
// Softstart by BlazinH
//****************************************************************************************************************
//****************************************************************************************************************
//SET SOFTSTART SPEED
const int SSloop = 30;
//****************************************************************************************************************

// Set to MODE1 for use with a typical H-Bride that requires PWM and 1 or 2 direction inputs
// Set to MODE2 for a 43A "Chinese" IBT-2 H-Bridge from e-bay or equiv
// Set to MODE3 for a Sabretooth setup in simple serial mode

#define MODE3

// Uncomment the following line to reverse the direction of Motor 1.
// #define REVERSE_MOTOR1

// Uncomment ONE of the following lines to enable analogue input AN5 as a scaler for the motion values.
// #define ENABLE_POT_SCALING
// #define ENABLE_NON_LINEAR_POT_SCALING

// Uncomment the following line to enable the second software serial port.
// NOTE: This is currently not working - leave commented out until fixed!!!
// #define SECOND_SERIAL


my pot is hall sensor 6127V1A180l5fs

I'm using another arduino sabertooth sketch, you can find it here. https://www.xsimulator.net/community/threads/smc3-sabretooth-test-version.6236/
This one, with soft start, for me does not work.

Hi Auriza, thank for your support. Can you please explain me where and how instal the zip file SMC3 v0.8 Sabretooth TEST.
Please...step by step...like if you are explain to a child. My knowledge of arduino, sabertooth and electronics and unfortunately equals at "zero" and although I have tried to study and read everything, missing the basics I can not understand. So I really need step by step explanation.
Thanks again
gigi