1. Do not share user accounts! Any account that is shared by another person will be blocked and closed. This means: we will close not only the account that is shared, but also the main account of the user who uses another person's account. We have the ability to detect account sharing, so please do not try to cheat the system. This action will take place on 04/18/2023. Read all forum rules.
    Dismiss Notice
  2. For downloading SimTools plugins you need a Download Package. Get it with virtual coins that you receive for forum activity or Buy Download Package - We have a zero Spam tolerance so read our forum rules first.

    Buy Now a Download Plan!
  3. Do not try to cheat our system and do not post an unnecessary amount of useless posts only to earn credits here. We have a zero spam tolerance policy and this will cause a ban of your user account. Otherwise we wish you a pleasant stay here! Read the forum rules
  4. We have a few rules which you need to read and accept before posting anything here! Following these rules will keep the forum clean and your stay pleasant. Do not follow these rules can lead to permanent exclusion from this website: Read the forum rules.
    Are you a company? Read our company rules
Shared accounts will be removed Plugin Downloads Zero spam policy Forum Rules

scn6 horizontal

Discussion in 'Commercial Simulators and Peripherie' started by genorimo, Oct 7, 2020.

  1. genorimo

    genorimo New Member

    Joined:
    Oct 17, 2016
    Messages:
    8
    Location:
    parmain
    Balance:
    - 119Coins
    Ratings:
    +0 / 0 / -0
    My Motion Simulator:
    SCN6, 6DOF
    wishing to spend on software lince simtool
    in the configuration of two horizontal cylinders scn6
    in order to have the same movements (surge and Vibration)
    thank you for giving me the axes configuration items
    genorimo, Oct 7, 2020
    #1
  2. noorbeast

    noorbeast VR Tassie Devil Staff Member Moderator Race Director

    Joined:
    Jul 13, 2014
    Messages:
    21,032
    Occupation:
    Innovative tech specialist for NGOs
    Location:
    St Helens, Tasmania, Australia
    Balance:
    147,890Coins
    Ratings:
    +10,880 / 54 / -2
    My Motion Simulator:
    3DOF, DC motor, JRK
    I am not sure what you mean, or what design you have in mind, can you clarify a bit more or perhaps provide a picture of what you want to do.
    noorbeast, Oct 7, 2020
    #2
  3. genorimo

    genorimo New Member

    Joined:
    Oct 17, 2016
    Messages:
    8
    Location:
    parmain
    Balance:
    - 119Coins
    Ratings:
    +0 / 0 / -0
    My Motion Simulator:
    SCN6, 6DOF
    my simulator is equipped with two cylinders placed horizontally (frame jcl)
    I use the software to lince logykal and I'd switched to simtool
    keeping the same effects or acceleration and braking
    and especially with the vibrations offered by the software lince,
    So you are there in the configuration parameter simtool about
    genorimo, Oct 7, 2020
    #3
  4. noorbeast

    noorbeast VR Tassie Devil Staff Member Moderator Race Director

    Joined:
    Jul 13, 2014
    Messages:
    21,032
    Occupation:
    Innovative tech specialist for NGOs
    Location:
    St Helens, Tasmania, Australia
    Balance:
    147,890Coins
    Ratings:
    +10,880 / 54 / -2
    My Motion Simulator:
    3DOF, DC motor, JRK
    I am presuming you have the SCNs communicating with SimTools, if not then please see the FAQ SCN section: https://www.xsimulator.net/community/faq/scn5-scn6.2/category

    It is important to in Axis Assignment go to Axis Limiting and for a SCN actuator select a value of 90%. This is very important to preserve your actuator in the long term. Not doing this can lead to mechanical damage: https://www.xsimulator.net/community/threads/english-guide-for-scn5-interface.5507/

    It sounds like you want to configure surge and perhaps heave, the latter for road affects, is that correct?

    Grab a copy of the SimTools manual and keep it handy for reference: https://www.xsimulator.net/community/faq/rtfm-start-with-the-official-simtools-documentation.117/

    And see the motion profile refinement tips here, in particular doing each axis individually and how to capture Max/Min values in the Tuning Center: https://www.xsimulator.net/community/faq/steps-to-create-a-motion-profile.228/
    Last edited: Oct 8, 2020
    noorbeast, Oct 8, 2020
    #4
  5. hideki

    hideki Active Member

    Joined:
    Feb 3, 2014
    Messages:
    169
    Location:
    Spain
    Balance:
    - 208Coins
    Ratings:
    +52 / 1 / -0
    My Motion Simulator:
    2DOF, SCN5
    LINCE has the same effects than SIMTOOLS (an others). Just play with simtools until you got it right, For example, as all games, cars and tracks are different, they may not give you exactly the same vibrations and you should "play" with the heave and pitch sliders to beging with. Then maybe surge and so on. There are so many sliders and parameters to tinker,,, Dont panic, Simtools is more complete and it takes a little to adjust
    hideki, Oct 8, 2020
    #5