1. Do not share user accounts! Any account that is shared by another person will be blocked and closed. This means: we will close not only the account that is shared, but also the main account of the user who uses another person's account. We have the ability to detect account sharing, so please do not try to cheat the system. This action will take place on 04/18/2023. Read all forum rules.
    Dismiss Notice
  2. For downloading SimTools plugins you need a Download Package. Get it with virtual coins that you receive for forum activity or Buy Download Package - We have a zero Spam tolerance so read our forum rules first.

    Buy Now a Download Plan!
  3. Do not try to cheat our system and do not post an unnecessary amount of useless posts only to earn credits here. We have a zero spam tolerance policy and this will cause a ban of your user account. Otherwise we wish you a pleasant stay here! Read the forum rules
  4. We have a few rules which you need to read and accept before posting anything here! Following these rules will keep the forum clean and your stay pleasant. Do not follow these rules can lead to permanent exclusion from this website: Read the forum rules.
    Are you a company? Read our company rules
Shared accounts will be removed Plugin Downloads Zero spam policy Forum Rules

Question SMC3 Problem

Discussion in 'DIY Motion Simulator Projects' started by YOSHI CUTTO, Nov 26, 2021.

  1. YOSHI CUTTO

    YOSHI CUTTO New Member

    Joined:
    Oct 24, 2021
    Messages:
    5
    Balance:
    24Coins
    Ratings:
    +0 / 0 / -0
    My Motion Simulator:
    2DOF
    Hello.

    I'm trying to build a motion simulator that uses Arduino and ibt2.

    The motor I am using is an ASME-04b.


    I am not confident in programming, so I disconnected the motor and the mode is activated by 24VDC (not very reasonable).


    I have a couple of problems with SMC3.


    If I check the connections and start SMC3 as described in the manual (KP400.MAX Limits, Clip input 255), the corresponding motors are turned off.


    Also, the blue gauge is still in the centre before you turn up the PWMax.


    As for the motor OFF, it turned ON when I lowered the MAX Limits.


    When the PWMax is increased while the status is ON, the yellow parameter increases.


    When I turn on the motor, the motor runs and the green line (presumably the potentiometer) runs until it swings past the MAX Limits.


    Are these problems with the SMC3 configuration? Or is it a problem with the SMC3 Arduino code? (Translated from Japanese as my English is not good enough)

    Attached Files:

    YOSHI CUTTO, Nov 26, 2021
    #1
  2. noorbeast

    noorbeast VR Tassie Devil Staff Member Moderator Race Director

    Joined:
    Jul 13, 2014
    Messages:
    21,157
    Occupation:
    Innovative tech specialist for NGOs
    Location:
    St Helens, Tasmania, Australia
    Balance:
    148,628Coins
    Ratings:
    +10,909 / 54 / -2
    My Motion Simulator:
    3DOF, DC motor, JRK
    Is there a pot connected to the motor?

    I thought the ASME-04b are servos, is that correct?
    • Agree Agree x 1
    noorbeast, Nov 26, 2021
    #2
  3. YOSHI CUTTO

    YOSHI CUTTO New Member

    Joined:
    Oct 24, 2021
    Messages:
    5
    Balance:
    24Coins
    Ratings:
    +0 / 0 / -0
    My Motion Simulator:
    2DOF
    Yes, ASME-04b is a servo motor.
    I cut the wire connecting the motor to the driver as a DC geared motor and connect it to the ibt-2.
    The Pot is connected through the shaft of the ASME-04b

    Attached Files:

    Last edited by a moderator: Nov 26, 2021
    YOSHI CUTTO, Nov 26, 2021
    #3
  4. Gadget999

    Gadget999 Well-Known Member

    Joined:
    Dec 27, 2015
    Messages:
    1,937
    Location:
    London
    Balance:
    11,850Coins
    Ratings:
    +475 / 9 / -0
    My Motion Simulator:
    2DOF, DC motor, Arduino, 6DOF
    Can you not use the servo motor correctly with its own motor driver and potentiometer ?
    Gadget999, Nov 26, 2021
    #4
  5. MarkusB

    MarkusB Well-Known Member Gold Contributor

    Joined:
    Jun 30, 2015
    Messages:
    552
    Location:
    Germany
    Balance:
    4,213Coins
    Ratings:
    +596 / 2 / -0
    My Motion Simulator:
    2DOF, 3DOF, DC motor, Arduino, Motion platform
    Exactly.

    As far as I remember, these servos have the same connector as usual RC servos, right?
    In this case you can simply connect the servo directly to the Arduino and an external power source.

    I don‘t have the link at hand, but I know that you can find Arduino sketches for RC servos in this forum, and wiring diagrams with external power sources can be found via Google.

    So what kind of simulator are you going to build?
    I know that these servos have been successfully used for G-seats, but they are probably not strong enough for moving an entire seat.
    • Agree Agree x 1
    MarkusB, Nov 27, 2021
    #5
  6. YOSHI CUTTO

    YOSHI CUTTO New Member

    Joined:
    Oct 24, 2021
    Messages:
    5
    Balance:
    24Coins
    Ratings:
    +0 / 0 / -0
    My Motion Simulator:
    2DOF
    Yes, it is probably the one that has the same wiring layout as the ibt-2.
    I would like to build a seat like the one in the picture that moves the seat through the shaft if possible.

    Attached Files:

    YOSHI CUTTO, Nov 27, 2021
    #6