1. Do not share user accounts! Any account that is shared by another person will be blocked and closed. This means: we will close not only the account that is shared, but also the main account of the user who uses another person's account. We have the ability to detect account sharing, so please do not try to cheat the system. This action will take place on 04/18/2023. Read all forum rules.
    Dismiss Notice
  2. For downloading SimTools plugins you need a Download Package. Get it with virtual coins that you receive for forum activity or Buy Download Package - We have a zero Spam tolerance so read our forum rules first.

    Buy Now a Download Plan!
  3. Do not try to cheat our system and do not post an unnecessary amount of useless posts only to earn credits here. We have a zero spam tolerance policy and this will cause a ban of your user account. Otherwise we wish you a pleasant stay here! Read the forum rules
  4. We have a few rules which you need to read and accept before posting anything here! Following these rules will keep the forum clean and your stay pleasant. Do not follow these rules can lead to permanent exclusion from this website: Read the forum rules.
    Are you a company? Read our company rules
Shared accounts will be removed Plugin Downloads Zero spam policy Forum Rules

Question feed back problem

Discussion in 'DIY Motion Simulator Projects' started by Ayad, Dec 30, 2022.

  1. Ayad

    Ayad Dr.

    Joined:
    Apr 11, 2022
    Messages:
    23
    Occupation:
    surgeon
    Location:
    Iraq
    Balance:
    - 425Coins
    Ratings:
    +1 / 0 / -0
    My Motion Simulator:
    2DOF, 3DOF, DC motor, Arduino
    after I finish and polay some days with 2 24 v motor rig and it was good ,after do another power supply ,my rig start to work funny ,I go back to previous and the rig still has funny work ,the hall sensor work for one side and the other one is not moving even by hand ,the voltemeter read studdy volt 1.79to 1.80 v ,even I use new hall sensor still same I change to 10 k potentiometer it still half and funny jerking movements ,I re i9nstall the arduino ,and change the wire ,this problem still with the annoying static electricity ,even I already isolate the GND of motors ,what is the problem what I should do please any one facing and resolve this problem
    Ayad
    Ayad, Dec 30, 2022
    #1
  2. noorbeast

    noorbeast VR Tassie Devil Staff Member Moderator Race Director

    Joined:
    Jul 13, 2014
    Messages:
    21,147
    Occupation:
    Innovative tech specialist for NGOs
    Location:
    St Helens, Tasmania, Australia
    Balance:
    148,577Coins
    Ratings:
    +10,903 / 54 / -2
    My Motion Simulator:
    3DOF, DC motor, JRK
    What control board are you using, perhaps it is faulty.
    noorbeast, Dec 30, 2022
    #2
  3. Ayad

    Ayad Dr.

    Joined:
    Apr 11, 2022
    Messages:
    23
    Occupation:
    surgeon
    Location:
    Iraq
    Balance:
    - 425Coins
    Ratings:
    +1 / 0 / -0
    My Motion Simulator:
    2DOF, 3DOF, DC motor, Arduino
    I use the chinese replica of arduino uno it was working good before with the IBT-2 , I think it some think with static electricity and only the reading from one side is affected when I change the postion the one with problem work well the other is not , by the way am using the screw sheild for arduino ,
    Ayad, Dec 30, 2022
    #3
  4. Fenton1969

    Fenton1969 New Member

    Joined:
    Oct 23, 2022
    Messages:
    1
    Balance:
    - 23Coins
    Ratings:
    +0 / 0 / -0
    My Motion Simulator:
    2DOF, AC motor, Arduino
    Som same problem here .i. trying to set things up all is oke
    But once i put the usb cable into the pc the rig starts living its owne live .and no program is running .
    Fenton1969, Feb 12, 2023
    #4
  5. noorbeast

    noorbeast VR Tassie Devil Staff Member Moderator Race Director

    Joined:
    Jul 13, 2014
    Messages:
    21,147
    Occupation:
    Innovative tech specialist for NGOs
    Location:
    St Helens, Tasmania, Australia
    Balance:
    148,577Coins
    Ratings:
    +10,903 / 54 / -2
    My Motion Simulator:
    3DOF, DC motor, JRK
    Something is very wrong, check the hardware and wiring for shorts.
    noorbeast, Feb 12, 2023
    #5
  6. noorbeast

    noorbeast VR Tassie Devil Staff Member Moderator Race Director

    Joined:
    Jul 13, 2014
    Messages:
    21,147
    Occupation:
    Innovative tech specialist for NGOs
    Location:
    St Helens, Tasmania, Australia
    Balance:
    148,577Coins
    Ratings:
    +10,903 / 54 / -2
    My Motion Simulator:
    3DOF, DC motor, JRK
    I don't knos what your mean by screw shield, can you please elaborate further.

    If using SimTools 2 make sure the PC language is set to English Local: https://www.xsimulator.net/community/faq/simtools-language-setting-bug-change-to-english-local.233/
    noorbeast, Feb 12, 2023
    #6