ARDUINO MEGA 2560 , 74HC595

Привет. Помогите , код для АРДУИНО

,mmm is it sirilic russian???

can you write english so we can read?

best regards from mexico

fer

Please use Google Translate to make your posts in English; more users will be able to understand and respond to you.

Thanks

[Цитата = "Historiker, сообщение: 55659, членом: 4542"] Пожалуйста, используйте Google Translate, чтобы сделать свои сообщения на английском языке; больше пользователей смогут понять и ответить вам.

Благодаря [/ QUOTE]
Нужен код

Пожалуйста, пост на английском языке, мы не можем помочь вам, если мы не можем понять вас.

Вот ссылка

https://translate.google.com/#ru/en/

I'm from Ukraine. I need Arduino code for this scheme.

I'm from Ukraine. I need Arduino code for this scheme.

Welcome Uporotiy-liss!! I know that you are also posting in the thread about the dashboard app. That might be the place to post again to ask for help using google translate.

Again, welcome to XSimulator.net

I gathered scheme. I want to make it work. Need a code for the tachometer.

Untested... but I think this should drive the display:

Code:

const int DataPin=7;
const int ClkPin=4;
const int LatchPin=8;
int TestLevel;
// Set LED Bar individual LEDs based on binary Mask (bits set = LED on)
void LEDBarSetLEDs(unsigned byte Mask)
{
    byte i;
         
    digitalWrite(ClkPin, LOW);   // make sure the serial clk pin is low
    digitalWrite(LatchPin, LOW);   // make sure the output latch pin is low
              
    for (i=7;i>=0;i--)
    {
        digitalWrite(DataPin, ((Mask>>i)&0x01));  // Set Data pin according to mask
        digitalWrite(ClkPin, HIGH);           // Clock the next data bit on rising clk pulse
        digitalWrite(ClkPin, LOW);  // Return clk low again ready for next cylcle
    }
    digitalWrite(LatchPin, HIGH);  // Latch data to output pins on rising edge
    digitalWrite(LatchPin, LOW);  // Return Latch low again ready for next cycle
}
// Set LED Bar level from 0 (off) to 8 (all LEDs on)
void LEDBarSetLevel(unsigned byte Level)
{
    byte i;
    if (Level=0) LEDBarSetLEDs(0x00);
    else if (Level=1) LEDBarSetLEDs(1);
    else if (Level=2) LEDBarSetLEDs(3);
    else if (Level=3) LEDBarSetLEDs(7);
    else if (Level=4) LEDBarSetLEDs(15);
    else if (Level=5) LEDBarSetLEDs(31);
    else if (Level=6) LEDBarSetLEDs(63);
    else if (Level=7) LEDBarSetLEDs(127);
    else if (Level=8) LEDBarSetLEDs(255);
}
// Test it....
void setup()
{
    pinMode(DataPin, OUTPUT);
    pinMode(ClkPin, OUTPUT);
    pinMode(LatchPin, OUTPUT);
}
void loop()
{
    for(TestLevel=0;TestLevel<8;TestLevel++)
    {
        LEDBarSetLevel(TestLevel);
        delay(500);
    }
}

Thank you. I will check.

How to run Arduino in the game? Your sketch fails. "stray\ in program"

Well blow me over, that's my old picture from a very old post, XDash.
I will search my drive, sure I still have the original code somewhere.
Picture of the boards I had made -

Contained a Rpm Light bar on one pcb, another had a 7 seg gear indicator and shift lights, the third board had a speedo and warning lights for oil and water. Might have to dust it off and fire it all back up.

Ok found my old code, lol was for the old software, now to test in SimTools.
Ok Rpm needs to be an 8bit decimal in order for this code to function under the GameDash.

Script needs to change the outputted Rpm to 0-255.
Command - Rxxx where xxx 0-255.

Ok need to plug it back into my test ard and fire it back up and change the code so we can use this with GameDash.
If ya beat me at it , I hope this helps.

I want it. Do you have diagram? Can collect this scheme of 5 74HC595?

Your code is loaded. Now see the work in a game like?