1. We have a few rules which you need to read and accept before posting anything here! Following these rules will keep the forum clean and your stay pleasant. Do not follow these rules can lead to permanent exclusion from this website: Read the forum rules.
    Are you a company? Read our company rules
  2. Do not share user accounts! Any account that is shared by another person will be blocked and closed. This means: we will close not only the account that is shared, but also the main account of the user who uses another person's account. We have the ability to detect account sharing, so please do not try to cheat the system. This action will take place on 04/18/2023. Read all forum rules.
    Dismiss Notice
  3. For downloading SimTools plugins you need a Download Package. Get it with virtual coins that you receive for forum activity or Buy Download Package - We have a zero Spam tolerance so read our forum rules first.

    Buy Now a Download Plan!
  4. Do not try to cheat our system and do not post an unnecessary amount of useless posts only to earn credits here. We have a zero spam tolerance policy and this will cause a ban of your user account. Otherwise we wish you a pleasant stay here! Read the forum rules
  5. We have a few rules which you need to read and accept before posting anything here! Following these rules will keep the forum clean and your stay pleasant. Do not follow these rules can lead to permanent exclusion from this website: Read the forum rules.
    Are you a company? Read our company rules
  6. Do not share user accounts! Any account that is shared by another person will be blocked and closed. This means: we will close not only the account that is shared, but also the main account of the user who uses another person's account. We have the ability to detect account sharing, so please do not try to cheat the system. This action will take place on 04/18/2023. Read all forum rules.
    Dismiss Notice
Shared accounts will be removed Plugin Downloads Zero spam policy Forum Rules

Move but not correct

Discussion in 'DIY Motion Simulator Building Q&A / FAQ' started by Kool7789, Jul 10, 2015.

Page 1 of 2
  1. Kool7789

    Kool7789 Member

    Joined:
    Jul 4, 2015
    Messages:
    37
    Location:
    Macau
    Balance:
    258Coins
    Ratings:
    +6 / 0 / -0
    My Motion Simulator:
    SCN5, SCN6
    Dear experts,
    I'm so sorry by asking and asking again. Finally in sin tools in test the motion (my Frex motion) moves. Also feel a bit shaking in game in assetto Corsa. But below show the photo the angle of my chair is on a side. I had follow totally the instruction I dunno where went wrong.
    Hope someone can help me on this.

    Thanks in advance
    image.jpg image.jpg image.jpg
    Kool7789, Jul 10, 2015
    #1
  2. noorbeast

    noorbeast VR Tassie Devil Staff Member Moderator Race Director

    Joined:
    Jul 13, 2014
    Messages:
    21,397
    Occupation:
    Innovative tech specialist for NGOs
    Location:
    St Helens, Tasmania, Australia
    Balance:
    150,037Coins
    Ratings:
    +10,993 / 54 / -2
    My Motion Simulator:
    3DOF, DC motor, JRK
    Can I clarify if the actuators move correctly when using the Output sliders for testing in the SimTools Game Engine?

    Can you please post screenshots of your settings.
    Last edited: Jul 12, 2015
    noorbeast, Jul 10, 2015
    #2
  3. Kool7789

    Kool7789 Member

    Joined:
    Jul 4, 2015
    Messages:
    37
    Location:
    Macau
    Balance:
    258Coins
    Ratings:
    +6 / 0 / -0
    My Motion Simulator:
    SCN5, SCN6
    im not sure if I copy the correct file for you guys to see. Many thanks for your helps.
    image.jpg image.jpg
    Kool7789, Jul 11, 2015
    #3
  4. Kool7789

    Kool7789 Member

    Joined:
    Jul 4, 2015
    Messages:
    37
    Location:
    Macau
    Balance:
    258Coins
    Ratings:
    +6 / 0 / -0
    My Motion Simulator:
    SCN5, SCN6
    image.jpg image.jpg I need to make it separately. I got nothing set in interface 3 and so on.
    Kool7789, Jul 11, 2015
    #4
  5. Kool7789

    Kool7789 Member

    Joined:
    Jul 4, 2015
    Messages:
    37
    Location:
    Macau
    Balance:
    258Coins
    Ratings:
    +6 / 0 / -0
    My Motion Simulator:
    SCN5, SCN6
    Also include my pc some Datas

    Attached Files:

    Kool7789, Jul 11, 2015
    #5
  6. Kool7789

    Kool7789 Member

    Joined:
    Jul 4, 2015
    Messages:
    37
    Location:
    Macau
    Balance:
    258Coins
    Ratings:
    +6 / 0 / -0
    My Motion Simulator:
    SCN5, SCN6
    image.jpg image.jpg image.jpg image.jpg image.jpg image.jpg image.jpg image.jpg image.jpg
    Anything I miss?
    Kool7789, Jul 11, 2015
    #6
  7. Kool7789

    Kool7789 Member

    Joined:
    Jul 4, 2015
    Messages:
    37
    Location:
    Macau
    Balance:
    258Coins
    Ratings:
    +6 / 0 / -0
    My Motion Simulator:
    SCN5, SCN6
    I'm trying to copy screen as much as I can. If still something you need to have to check let me know.
    I know in quiet near to the motion movements.
    Hope it will be soon.

    Again thank you all so much for your kindly help. Thanks a lot. Have a nice weekend too.
    Kool7789, Jul 11, 2015
    #7
  8. Kool7789

    Kool7789 Member

    Joined:
    Jul 4, 2015
    Messages:
    37
    Location:
    Macau
    Balance:
    258Coins
    Ratings:
    +6 / 0 / -0
    My Motion Simulator:
    SCN5, SCN6
    Normally when it start (in Straight back) I switch on the electricity the chair will move like the attached photo. Red to red arrow front and back and lean on a side after or Greeb to Green arrow. It seems depending the mood on which way.

    Attached Files:

    Kool7789, Jul 11, 2015
    #8
  9. noorbeast

    noorbeast VR Tassie Devil Staff Member Moderator Race Director

    Joined:
    Jul 13, 2014
    Messages:
    21,397
    Occupation:
    Innovative tech specialist for NGOs
    Location:
    St Helens, Tasmania, Australia
    Balance:
    150,037Coins
    Ratings:
    +10,993 / 54 / -2
    My Motion Simulator:
    3DOF, DC motor, JRK
    I did ask earlier if the actuators move correctly when using the Output sliders for testing in the SimTools Game Engine?
    noorbeast, Jul 12, 2015
    #9
  10. Kool7789

    Kool7789 Member

    Joined:
    Jul 4, 2015
    Messages:
    37
    Location:
    Macau
    Balance:
    258Coins
    Ratings:
    +6 / 0 / -0
    My Motion Simulator:
    SCN5, SCN6
    i don't think so it moves correctly. Coz is not moving straight. And seems only one actuator is moving.
    once connect to game engine it moves one Conner side and to the other Conner side then stop like the first picture that i post it, instead moving forward and backward I think it should be.
    Kool7789, Jul 12, 2015
    #10
  11. Kool7789

    Kool7789 Member

    Joined:
    Jul 4, 2015
    Messages:
    37
    Location:
    Macau
    Balance:
    258Coins
    Ratings:
    +6 / 0 / -0
    My Motion Simulator:
    SCN5, SCN6
    At the engine the below two columns (last two columns, seems is Yaw and another) slider it moves but just Conner to Conner and one way.
    It means my left back moves to forward right. And when I put it yaw a 100% and the other -100% the chair will be straight in that testing.
    Kool7789, Jul 12, 2015
    #11
  12. noorbeast

    noorbeast VR Tassie Devil Staff Member Moderator Race Director

    Joined:
    Jul 13, 2014
    Messages:
    21,397
    Occupation:
    Innovative tech specialist for NGOs
    Location:
    St Helens, Tasmania, Australia
    Balance:
    150,037Coins
    Ratings:
    +10,993 / 54 / -2
    My Motion Simulator:
    3DOF, DC motor, JRK
    So have I got it correct that only one actuator moves?

    It will likely be easier if you just post a video that shows the rig and screen at the same time, rather than trying to explain it.
    noorbeast, Jul 12, 2015
    #12
  13. Kool7789

    Kool7789 Member

    Joined:
    Jul 4, 2015
    Messages:
    37
    Location:
    Macau
    Balance:
    258Coins
    Ratings:
    +6 / 0 / -0
    My Motion Simulator:
    SCN5, SCN6
    Yup. I will drop it tonight coz here is 2:57pm now and I'm out. I will upload it 6 hrs later. Sorry about that
    • Useful Useful x 1
    Kool7789, Jul 12, 2015
    #13
  14. insanegr

    insanegr !N$@n€

    Joined:
    Jan 14, 2014
    Messages:
    504
    Location:
    Athens
    Balance:
    16,720Coins
    Ratings:
    +499 / 1 / -0
    My Motion Simulator:
    2DOF, DC motor, Arduino
    does one actuator only move? Did you check your wiring again or swap actuators not the power supply and the rs485?? Are you using one power supply per actuator?
    insanegr, Jul 12, 2015
    #14
  15. Kool7789

    Kool7789 Member

    Joined:
    Jul 4, 2015
    Messages:
    37
    Location:
    Macau
    Balance:
    258Coins
    Ratings:
    +6 / 0 / -0
    My Motion Simulator:
    SCN5, SCN6
    Yes I'm using the power supply by actuator.
    Kool7789, Jul 12, 2015
    #15
  16. Kool7789

    Kool7789 Member

    Joined:
    Jul 4, 2015
    Messages:
    37
    Location:
    Macau
    Balance:
    258Coins
    Ratings:
    +6 / 0 / -0
    My Motion Simulator:
    SCN5, SCN6
    I just cut off the line of Simcon Motion and plug it into RS485.
    Kool7789, Jul 12, 2015
    #16
  17. noorbeast

    noorbeast VR Tassie Devil Staff Member Moderator Race Director

    Joined:
    Jul 13, 2014
    Messages:
    21,397
    Occupation:
    Innovative tech specialist for NGOs
    Location:
    St Helens, Tasmania, Australia
    Balance:
    150,037Coins
    Ratings:
    +10,993 / 54 / -2
    My Motion Simulator:
    3DOF, DC motor, JRK
    noorbeast, Jul 12, 2015
    #17
  18. Kool7789

    Kool7789 Member

    Joined:
    Jul 4, 2015
    Messages:
    37
    Location:
    Macau
    Balance:
    258Coins
    Ratings:
    +6 / 0 / -0
    My Motion Simulator:
    SCN5, SCN6
    Yup this is what i had followed
    Kool7789, Jul 12, 2015
    #18
  19. Kool7789

    Kool7789 Member

    Joined:
    Jul 4, 2015
    Messages:
    37
    Location:
    Macau
    Balance:
    258Coins
    Ratings:
    +6 / 0 / -0
    My Motion Simulator:
    SCN5, SCN6
    The first video from youtube is when i click the Simtools and he moves
    the second one is in the output setting. please refer to the youtube link below



    thanks in advance
    Kool7789, Jul 12, 2015
    #19
  20. noorbeast

    noorbeast VR Tassie Devil Staff Member Moderator Race Director

    Joined:
    Jul 13, 2014
    Messages:
    21,397
    Occupation:
    Innovative tech specialist for NGOs
    Location:
    St Helens, Tasmania, Australia
    Balance:
    150,037Coins
    Ratings:
    +10,993 / 54 / -2
    My Motion Simulator:
    3DOF, DC motor, JRK
    noorbeast, Jul 12, 2015
    #20
Page 1 of 2