1. This Software is no longer supported by us. Please download the new motion control software SimTools.
    Dismiss Notice
  2. Do not share user accounts! Any account that is shared by another person will be blocked and closed. This means: we will close not only the account that is shared, but also the main account of the user who uses another person's account. We have the ability to detect account sharing, so please do not try to cheat the system. This action will take place on 04/18/2023. Read all forum rules.
    Dismiss Notice
  3. For downloading SimTools plugins you need a Download Package. Get it with virtual coins that you receive for forum activity or Buy Download Package - We have a zero Spam tolerance so read our forum rules first.

    Buy Now a Download Plan!
  4. Do not try to cheat our system and do not post an unnecessary amount of useless posts only to earn credits here. We have a zero spam tolerance policy and this will cause a ban of your user account. Otherwise we wish you a pleasant stay here! Read the forum rules
  5. We have a few rules which you need to read and accept before posting anything here! Following these rules will keep the forum clean and your stay pleasant. Do not follow these rules can lead to permanent exclusion from this website: Read the forum rules.
    Are you a company? Read our company rules
This Software is no longer supported by us. Shared accounts will be removed Plugin Downloads Zero spam policy Forum Rules

pitch and roll data from NR2003

Discussion in 'Force-Sender & Plugins' started by rft, May 27, 2008.

  1. rft

    rft New Member

    Joined:
    May 25, 2008
    Messages:
    3
    Balance:
    0Coins
    Ratings:
    +0 / 0 / -0
    G'day,
    Does anyone know how to get the pitch and roll chassis data from NR2003? I only need these two variables.
    rft, May 27, 2008
    #1
  2. egoexpress

    egoexpress Active Member

    Joined:
    Dec 13, 2006
    Messages:
    3,839
    Location:
    Germany - Frankfurt/M
    Balance:
    421Coins
    Ratings:
    +10 / 1 / -0
    Hi,

    start the Force-Sender, select the NR2003 Plugin, start NR2003.

    [​IMG]

    Then open the Force-Profiler, and use the following effect numbers to copy them as g-effects to the list below:
    22 = long accelleration
    25 = lat accelleration

    regards
    Christian
    egoexpress, May 27, 2008
    #2
  3. rft

    rft New Member

    Joined:
    May 25, 2008
    Messages:
    3
    Balance:
    0Coins
    Ratings:
    +0 / 0 / -0
    Thanks Chris,

    I was attempting to sort out the data variables from the sample telemetry tsample.cpp that is included with the NR2003 game. I am also going to attempt to move gauges with the data later on.
    rft, May 27, 2008
    #3
  4. egoexpress

    egoexpress Active Member

    Joined:
    Dec 13, 2006
    Messages:
    3,839
    Location:
    Germany - Frankfurt/M
    Balance:
    421Coins
    Ratings:
    +10 / 1 / -0
    You could use Thanos Controller to make some servo DIY gauges. With effect 21 you would be able to display the speed. I think it would be possible as well to output the rpm, if you asked for it...when you have the hardware basis established.

    diy-analog-servo-car-instruments-t890.html

    Regards
    Christian
    egoexpress, May 27, 2008
    #4
  5. rft

    rft New Member

    Joined:
    May 25, 2008
    Messages:
    3
    Balance:
    0Coins
    Ratings:
    +0 / 0 / -0
    Hey Chris,

    Thanks, I will fool around with this and see what happens.
    rft, May 27, 2008
    #5