-
Do not share user accounts! Any account that is shared by another person will be blocked and closed. This means: we will close not only the account that is shared, but also the main account of the user who uses another person's account. We have the ability to detect account sharing, so please do not try to cheat the system. This action will take place on 04/18/2023. Read all forum rules.Dismiss Notice
-
For downloading SimTools plugins you need a Download Package. Get it with virtual coins that you receive for forum activity or Buy Download Package - We have a zero Spam tolerance so read our forum rules first.
Buy Now a Download Plan! -
Do not try to cheat our system and do not post an unnecessary amount of useless posts only to earn credits here. We have a zero spam tolerance policy and this will cause a ban of your user account. Otherwise we wish you a pleasant stay here! Read the forum rules
-
We have a few rules which you need to read and accept before posting anything here! Following these rules will keep the forum clean and your stay pleasant. Do not follow these rules can lead to permanent exclusion from this website: Read the forum rules.
Are you a company? Read our company rules
Recent Activity
Activity stream for all registered members at Motion Simulator Community.
-
Raulmerlos posted a new thread.
Request (Feature) Does anyone know how to connect a frequency converter and configure simm tools?
¿Alguien sabe cómo conectar un convertidor de frecuencia y configurar herramientas simm?
Forum: Forum and Website
May 5, 2024 at 10:27 -
noorbeast replied to the thread Question Sensor scale.
You need to consider how the pot is driven, here is an example:...
May 5, 2024 at 09:23 -
Krzysztof Dej posted a new thread.
Question Sensor scale
Hi I want to try make linear actuator but with DC motor and smc3. I must make gearshift for sensor to make propper long movent but is...
Forum: DIY Motion Simulator Building Q&A / FAQ
May 5, 2024 at 08:10 -
noorbeast replied to the thread motor 1 vs motor 2.
What hardware are you using and have you tested it for faults by swapping the motors over on the control board?
May 5, 2024 at 04:43 -
jarena replied to the thread motor 1 vs motor 2.
motors are new. on motor 1 PWMAX was at 90 or 100 and it started to move. but motor 2 i went up to 140 and nothing no movement.
May 5, 2024 at 04:17 -
noorbeast liked PhillyNJ's post in the thread Showroom My 2DoF project [In work].
Hi Everyone, I am about 75% done with my 2DoF project that I plan on using with FS2020. As a new member, I really enjoy seeing all the...
May 5, 2024 at 02:59
-
PhillyNJ posted a new thread.
Showroom My 2DoF project [In work]
Hi Everyone, I am about 75% done with my 2DoF project that I plan on using with FS2020. As a new member, I really enjoy seeing all the...
Forum: DIY Motion Simulator Projects
May 5, 2024 at 02:01 -
noorbeast liked Sebastian2's post in the thread My 3 DOF with heave.
Noorbeast's advice was helpful. I deactivated all DOFs but roll and i found that anti roll over was working as intended. Then I slowly...
May 5, 2024 at 00:21 -
noorbeast replied to the thread motor 1 vs motor 2.
If you keep increasing PWMAX with motor 2 at what value does it move? Are the motors new or second hand? Just checking that you are...
May 5, 2024 at 00:20 -
Gabriel the simracer liked Peacemaker105's post in the thread Peacemakers 6dof Unicorn Build.
Well @JAD will be happy, i fixed my rotating actuators today :P haha. I also got a test in with some Dirt and put the rig and monitor...
May 4, 2024 at 17:57 -
Sebastian2 replied to the thread My 3 DOF with heave.
Noorbeast's advice was helpful. I deactivated all DOFs but roll and i found that anti roll over was working as intended. Then I slowly...
May 4, 2024 at 17:45 -
Radioproffi replied to the thread DOF reality SFU specs and motors.
standard motors in this size have 2 sizes of shafts - 9 or 11 mm, you can use CNC-coupling or buy with SFU units size what you need
May 4, 2024 at 17:39 -
Mariano Tarnogol replied to the thread DOF reality SFU specs and motors.
Great info, thanks. Shaft diameter and lenght are important? Or I can work it out with some CNC coupling?
May 4, 2024 at 17:37 -
jarena posted a new thread.
motor 1 vs motor 2
Hi guys, I don't get it. when I do the simtools test of the motors , I do the test of motor 1 increasing PWMAX slowly and once I get to...
Forum: DIY Motion Simulator Building Q&A / FAQ
May 4, 2024 at 17:09 -
Radioproffi attached a file to the thread DOF reality SFU specs and motors.
1200-1500 rpm motor preferred, 1-1.5 n.m. on motor shaft flange mounting holes diameter 65 or 75 mm
May 4, 2024 at 16:56