1. Do not share user accounts! Any account that is shared by another person will be blocked and closed. This means: we will close not only the account that is shared, but also the main account of the user who uses another person's account. We have the ability to detect account sharing, so please do not try to cheat the system. This action will take place on 04/18/2023. Read all forum rules.
    Dismiss Notice
  2. For downloading SimTools plugins you need a Download Package. Get it with virtual coins that you receive for forum activity or Buy Download Package - We have a zero Spam tolerance so read our forum rules first.

    Buy Now a Download Plan!
  3. Do not try to cheat our system and do not post an unnecessary amount of useless posts only to earn credits here. We have a zero spam tolerance policy and this will cause a ban of your user account. Otherwise we wish you a pleasant stay here! Read the forum rules
  4. We have a few rules which you need to read and accept before posting anything here! Following these rules will keep the forum clean and your stay pleasant. Do not follow these rules can lead to permanent exclusion from this website: Read the forum rules.
    Are you a company? Read our company rules
Shared accounts will be removed Plugin Downloads Zero spam policy Forum Rules

WIP - Interface for Stewart Platform Control

Discussion in 'Official Companion Apps' started by eaorobbie, Sep 18, 2015.

Page 3 of 3
  1. bruce stephen

    bruce stephen Hammer doesnt fix it, must be electrical

    Joined:
    Jun 7, 2015
    Messages:
    1,286
    Occupation:
    general contractor
    Location:
    michigan
    Balance:
    9,112Coins
    Ratings:
    +1,238 / 9 / -0
    My Motion Simulator:
    2DOF, DC motor, Arduino, Motion platform, 6DOF
    in both of their threads they discuss using Ian's bff software.
    I'm not sure what controller combo @SeatTime uses but.
    @wannabeaflyer2 is using a thanos controller along with sabertooth. @SilentChill is using Arduino and sabertooths. (He may have switched controllers I'm not sure) but he is running simtools.
    My current 6dof runs on Arduino and monster motos with simtools.
    Last edited: Jan 24, 2018
    bruce stephen, Jan 24, 2018
    #41
  2. Zennix

    Zennix New Member Gold Contributor

    Joined:
    Mar 4, 2018
    Messages:
    12
    Location:
    Bayern
    Balance:
    66Coins
    Ratings:
    +29 / 0 / -0
    My Motion Simulator:
    2DOF
    Hi,
    any news on this?
    Searched a lot in the forum, but could not find any other thread that continous this.
    Find it very interesting not to use a separat part for calculation.

    Greetings / Zennix
    Zennix, Jan 1, 2019
    #42
  3. BlazinH

    BlazinH Well-Known Member

    Joined:
    Oct 19, 2013
    Messages:
    2,145
    Location:
    Oklahoma City, USA
    Balance:
    16,622Coins
    Ratings:
    +1,835 / 32 / -1
    I afraid this thread is still at this stage.
    .jpg
    At this point I think its fair to say its dead, dead, dead and empty promises!
    BlazinH, Jan 1, 2019
    #43
  4. pmvcda

    pmvcda aka FlyPT

    Joined:
    Nov 3, 2010
    Messages:
    2,163
    Location:
    Portugal
    Balance:
    15,284Coins
    Ratings:
    +2,539 / 17 / -0
    My Motion Simulator:
    6DOF
    pmvcda, Jan 1, 2019
    #44
  5. Zennix

    Zennix New Member Gold Contributor

    Joined:
    Mar 4, 2018
    Messages:
    12
    Location:
    Bayern
    Balance:
    66Coins
    Ratings:
    +29 / 0 / -0
    My Motion Simulator:
    2DOF
    Thank you,
    thats very bad. I have build my 2dof prototype with a special controller for brushless linear actuators and want now starting to build a 6dof. I know two other guys they are at the same stage as me.
    Thanks / Zennix
    Zennix, Jan 1, 2019
    #45
  6. Zennix

    Zennix New Member Gold Contributor

    Joined:
    Mar 4, 2018
    Messages:
    12
    Location:
    Bayern
    Balance:
    66Coins
    Ratings:
    +29 / 0 / -0
    My Motion Simulator:
    2DOF
    @pmvcda
    Sorry we wrote at the same time. Thanks a lot, I will try.
    Thanks / Zennix
    Zennix, Jan 1, 2019
    #46
Page 3 of 3