Showroom My Diy 2dof RC test then 2dof wiper motor diary

OK it was a broken motor controller

Hi I have lots of fun with my 2dof. And my dream come true. With basshaker and vr for me is like Wow. I spend lots of time to create motion profile to specific games and have some thoughts how to get the ultimate immersion for me @noorbeast My friend
Is it posibble to relay surge and sway signal and add some pads to the chair for symulate gforces works on my back when accelerate and to my side on sway. Is it possible some how or i must do something else?

Which link is for me? I don't fully understand i must modify existing code? I want to add 3 servo to 2dof that work same time. I found serwo code but this is not for me. Sorry my language barrier is i think to high. Every link I read is about serwo but not 2dof and gseat so I don't know how to add another motors

OK sim tools can handle to 6 profiles so I can add another Diy for my rig
I will try to do something like this
https://www.xsimulator.net/community/threads/wip-racingmats-closed-circuit-gseat.14071/

https://www.xsimulator.net/community/faq/arduino-code-for-servo-g-seats.318/
Code and sim tools settings from this link
I need to add 3 serwo ; 2 for sway (left, right) L, F Axis2a, 2b with settings Simtools 2.4 to prevent negative vales and movement https://www.xsimulator.net/communit...p-to-prevent-negative-vales-and-movement.340/
SIM tools is wonderful software it can hold to 6!!!! Interfaces so I set it up to interface 2 with another port with my old serwo to check it. It's work like a charm so now I want to my serwo and other stuff like from RacingMat's https://www.xsimulator.net/community/threads/wip-racingmats-closed-circuit-gseat.14071/

Hi I have problem when and how to set max min values on tuning center? I don't have available capture max min button. Also when I try to set this in game I saw that my Richard burns rally profile is connected to all interfaces. When I try to set it for interface 2 it changed to interface 1 also. On interface 1 I have 2dof chair how to set profile to gseat axis without changing 2dof? @noorbeast @RacingMat @MarkusB

ok there it is. Maybe i start understand , am i right? i need to add another axis (b ?) to existing profile. there r my testing settings in b axis assignment i put 2 motors that will pomp pressure for surge , is it ok ?

OK and for sway? For exemple letters F and B
When I want to prevent negative values? ~F<Axis1b>~B<Axis2b>~? ) And set it in tuning center like on picture? Is this won't affect 2dof tuning settings? Or better use modified arduino code lift only? (when I use modified code No need to set tuning center like on screen?)

I can't becouse of tuning center existing for 2dof?

I make gseat axis like 1b, 2b and it's works but serwo works only when push brakes, i need it to works when push throttle? And this is running center goes i think. How to set it?@noorbeast @RacingMat @MarkusB

OK i try in the evening. Thanks for answer

Yes but I checked the DIR box and serwo works only with braking no

Yes but I think I checked this and this no the direction problem but bo movement at all on the throttle side, only all movement when braking

 Thank You for advice. I made it
So:
1. create another axes on (a) section like:
Axis3a,....
2. Allocate % and run game.
3. Run tuning center and change preferred section and up or down and other set 0
4. Save for axis assignment B!!!!
5. Set tuning center as previous.
6. Save for A axis assignment.
7. Change on sim tools interface settings letter A to B like Axis 3a to Axis3b.
8. Change on Axis Assignment
DONE
U have movement only for (in my case) throttle
Thank you @noorbeast for tolerate me through my tough learning

I wanna ask about Surge force. When I'm in the full throttle chair leans back ok when I release throttle chair come back ok but when I'm on the throttle long time that chair lean back it's start to come back to middle point. How to change that it will be returning more subtly (slowly)? @noorbeast is it traction loss filter?

I have some problem. My serwos arrived and I wanted to check it out connect all to 5v and 4,5,6 pins and when I try to check how it work on sim tools they worked well but when I try to quick change directions sim tools crashed. Any ideas?